Generally, there is a volt outlet behind the range. It's really pretty easy to add this outlet and its feed. If you feel at all uncomfortable about working on an electrical circuit, then it might be best the call a professional. If you think you're up to the challenge, you can follow these simple steps. When installing an electric dryer for the first time or in a building lacking an electric dryer outlet , you'll need to install and wire an electric dryer outlet. With the proper wiring, outlet, a few choice electrical tools, and these easy steps, you too can install the outlet like a pro.
There is a special outlet for feeding an electric range , which you may or may not have to add. Thes simple instruction will help you do just that. Split outlets control lamps that plug into an outlet in a room of your home, like a living room. These outlets are converted in such a way that a switch in your home can run one-half of the outlet while the other half is hot all the time.
With these simple instructions, you too can wire and install a split outlet. Isolated-ground receptacles have their uses in today's home. If necessary, remove the outer sheathing on the NM cable by slitting the jacket with a cable ripper, and then trimming away the sheathing and paper insulation with a utility knife or wire cutters. Then, cut off the ends of the individual conducting wires so that no more than 6 to 7 inches extends past the front of the box.
If you're replacing an old outlet receptacle, you probably will not need to prepare the cables or strip the individual wires. If you are replacing an old outlet receptacle, make sure that the ends of the wires are in good condition and have no nicks or scorch marks; if they do, trim off the damaged portion and strip away insulation from the end of the wire. Follow the manufacturer's recommendations when using wire connectors to make connections, such as when pigtailing.
Stripping too much insulation can leave bare wire exposed under the wire connector's cap. Many outlet receptacles have a stripping gauge imprinted on the back of the device to tell you how far the wires should be stripped. Install pigtail wires if there is more than one cable in the box.
Using a scrap of the same type of circuit cable, cut 6-inch lengths of each type of wire in the cable. Join the bare copper or green insulated pigtail to the ground wires in the circuit cables, using a wire connector, following the manufacturer's directions. Do the same with the white neutral pigtail, then the black hot pigtail, so you have one ground, one white, and one black pigtail connected to the circuit wires.
If the electrical box is metal, install an additional grounding pigtail and connect it to the ground screw on the box. Form a J-shaped hook on the end of each wire or pigtail , using needle-nose pliers. Fit the hooked end of the ground wire around the ground screw on the new receptacle. The wire should hook around the screw in a clockwise fashion. This way, the screw will close the hook as you tighten the screw.
Use needle-nose pliers to squeeze the hook closed around the threaded shank of the screw. Tighten the ground screw with a screwdriver. The hook should fit snugly around the shank of the screw. Connect the white neutral wire or white pigtail to one of the silver neutral screw terminals on the receptacle, hooking the wire around the screw terminal in a clockwise direction. The insulation should just touch the screw terminal. Connect the black hot wire or black pigtail to one of the brass hot screw terminals on the receptacle.
I have a 20A breaker V which services one outlet dart board game ; I am thinking of splitting off of that line right before the outlet in a junction box to supply two 80W fluorescent fixtures. Will Romex be OK to use? Use 12ga copper wire for a 20 amp circuit. Not Helpful 6 Helpful How do I connect a mid run outlet at the end of the run?
Do I need a single pole outlet? No, since it's a mid run outlet and not the last outlet ending the circuit, you need a triple pole outlet.
That way you can run your nomex to the outlet off the one set of screws, and then feed another line off the other set of screws to continue the circuit and feed the next outlet. Not Helpful 6 Helpful 9.
I have a 20A double outlet I'm planning on installing outside. The wire I'm using has a green, black and white wire, and the outlet has two screws on each side. What do I do to get the both plugs to work? Connect the black hot and white neutral to the screws that say load and the green ground to the green screen on the bottom, and they both should work.
Not Helpful 2 Helpful 3. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube.
Connect the black wire to the circuit breaker last. Helpful 22 Not Helpful You may purchase an outlet tester quite inexpensively at a home center or hardware store. This device has several lights to indicate proper outlet wiring and fault conditions so you know you did the job correctly.
Helpful 16 Not Helpful When cutting into the wall for your new outlet, make sure there is not stud in the way. Studs are usually located on 16 inch You can locate the studs with an inexpensive stud finder available from your local home center or hardware store. Helpful 1 Not Helpful 0. Be sure to turn the main breaker OFF whenever working inside your electrical panel. Helpful 13 Not Helpful 4. Even with the main breaker turned OFF there is still power going to the main breaker unless there is an outside switch before the panel.
Remove rings and other metal from your hands and wear gloves and proceed with caution. Helpful 12 Not Helpful 9. Check your local code for Ground Fault and Arc Fault protection requirements. Helpful 9 Not Helpful 9. Use ONLY breakers determined by the manufacturer for use in the panel on the inside of the panel door there should at least be the manufacturer's name and model of the panel, and most likely, a list of all breakers approved for use.
Helpful 4 Not Helpful 5. You Might Also Like How to. How to. Master Electrician. Expert Interview. About This Article. Co-authored by:. Wrap the end of the black wire around the black screw and the white wire on the silver screw. Attach the end of the copper ground wire to the green screw that's either on the top or bottom of the outlet.
Make sure the loops go around the screws clockwise so the current can travel at full strength. Once all the wires are attached, tighten all of the screws so they have a secure connection. Screw the outlet into the exterior box to hold it in place. Hold the outlet inside of the exterior box so the screwholes line up with one another and so the wires are tucked in the back of the box. Use either wood screws or masonry anchors depending on whether you have wood or concrete exterior walls.
Tighten the screws on the outlet to the sides of the box so it's secured in place. Some exterior boxes allow you to screw the outlets directly into them so you don't need to put more screws in your siding. Turn on the power to the outlet to test if it works. Flip the switch on your circuit box so your outlets have power again. Plug your outlet tester into the indoor and outdoor outlets to see if they're working.
Check the key on top the tester to determine if the wiring for your outlets are correct. If the outlets still aren't working or the tester shows the wiring is wrong, turn off the circuit again and check the wires. Ricardo Mitchell. Since existing outlets already have their load maximums calculated, you'll run into less trouble if you install outdoor outlets on their own circuits.
Yes No. Not Helpful 0 Helpful 0. Include your email address to get a message when this question is answered. Never work on electrical wires while the power is still on since you could shock or electrocute yourself. Helpful 0 Not Helpful 0. Always wear safety glasses while you're working with power tools so you don't get anything in your eyes.
If you don't feel comfortable wiring the outlet yourself, call a professional electrician to do the work for you. You Might Also Like How to. How to. Expert Interview. More References 7. About This Article. Co-authored by:. Co-authors: 4. Updated: September 30, Categories: Yard and Outdoors. Thanks to all authors for creating a page that has been read 32, times.
Reader Success Stories John R. Feb 17,
0コメント